West-control-solutions KS 800 CANopen Interface Manual Uživatelský manuál Strana 45
- Strana / 46
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
KS 800 CAN-Interface
11.4 Cable parameters
ISO 11898-2 defines some DC or AC parameters for the cables which can be used in CAN bus
networks (typically, pairwisely twisted cables with defined electrical properties are used). The
important AC parameters are 120 Ohm cable impedance and a nominal _propagation delay_ of
5 ns/m ! Recommendations for the bus cables and terminating resistors are given in the following
table:
Bus-length Bus-cabel (Z: 120 Ohm, tp: 5ns/m Terminating-
resistance
Max. Bit-rate
Spec.
resistance
Cabel-size
0 ..40 m 70 mOhm/m 0,25mm², 0,34mm²
AWG 23, AWG 22
124 Ohm, 1% 1 MBd
@ 40m
40 m .. 300 m <60 mOhm/m 0,34mm², 0,6mm²
AWG 22, AWG 20
127 Ohm, 1%
*
) > 500 kBd
@ 100m
300 m .. 600 m <40 mOhm/m 0,5mm², 0,6mm²
AWG 20
127 Ohm, 1%
*
) > 100 kBd
@ 500m
600 m ..1 km <26 mOhm/m 0,75mm², 0,8mm²
AWG 18
127 Ohm, 1%
*
) >50kBd
@1km
*
) With very long cables, a higher value for the terminating resistor (150 .. 300 Ohm) is useful for
reducing the attenuation.
Further recommendations for CAN networks (especially large ones):
Galvanic isolation is necessary with very long bus cables (e.g. 400m).
A separate ground line is purposeful.
The voltage drop (potential difference) between the transceiver ground potentials should
be low (smaller than 2 V, supply voltage from power supply in the middle of the cable).
The total input resistance of bus nodes should be > 500 Ohm.
Any tap lines should be as short as possible to prevent/reduce reflections, e.g. 6m @
500kbit (DeviceNet).<1mwith higher bit rates !
For further information, refer to ODVA (DeviceNet), CiA (CANopen), various chip manufacturers
and Internet.
9499 040 49511 45
- 1 Introduction 5
- 2 Service data objects 7
- 3 Process data objects 9
- 4 OP mode / pre-OP mode 15
- 6 Nodeguarding / Lifeguarding 17
- 8 Object directory 25
- KS 800 CAN-Interface 26
- 26 9499 040 49511 26
- FB input 27
- FB analog out 27
- FB controller 27
- 28 9499 040 49511 28
- 9499 040 49511 29 29
- FB alarm 30
- 9499 040 49511 31 31
- 9499 040 49511 33 33
- 34 9499 040 49511 34
- Caution! 37
- Instrument configuration 38
- Channel configuration 38
- Instrument parameters 39
- Channel parameters 39
- 10 Application example 40
- 11 CAN Physical Layer 43
Související produkty a manuály pro Zařízení West-control-solutions KS 800 CANopen Interface Manual
(318 stránky)Pilz PSSu K S 8DI 8DO 0.5 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Czujniki Pilz PSSu K S 8DI 8DO 0.5.
Dostarczamy 1 pdf podręczników Pilz PSSu K S 8DI 8DO 0.5 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce